GENERAL ELECTRIC RTXRRN 自动化电动遥控开关

Description

GENERAL ELECTRIC RTXRRN 自动化电动遥控开关的技术参数

由于 GENERAL ELECTRIC（通用电气，GE）的产品型号众多且不断更新，RTXRRN 自动化电动遥控开关的具体技术参数可能因产品版本、应用场景或定制需求而有所不同。不过，根据 GE 工业自动化产品的通用技术特点和行业规范，可推测该型号可能包含以下关键技术参数：

---

1. 电气参数

• 额定电压：
  • 通常支持 24VDC、120VAC、240VAC 或 480VAC 等工业标准电压。
• 额定电流：
  • 根据负载类型，电流范围可能为 5A 至 100A，具体取决于开关的额定容量。
• 功率因数：
  • 通常为 0.8 至 1.0（感性负载）。
• 绝缘电阻：
  • 一般不低于 10MΩ（500VDC 测试）。
• 介电强度：
  • 通常为 2000VAC（1 分钟，无击穿）。

---

2. 机械参数

• 操作方式：
  • 电动操作，支持远程控制（如 PLC、DCS 或 SCADA 系统）。
• 操作循环次数：
  • 机械寿命通常为 100 万次以上，电气寿命根据负载类型可能为 10 万次至 50 万次。
• 操作时间：
  • 闭合时间：≤ 50ms
  • 断开时间：≤ 30ms
• 安装方式：
  • DIN 导轨安装或面板安装。

---

3. 环境参数

• 工作温度：
  • -25°C 至 +70°C（标准型），或 -40°C 至 +85°C（宽温型）。
• 存储温度：
  • -40°C 至 +85°C。
• 相对湿度：
  • 5% 至 95%（无凝露）。
• 防护等级：
  • 通常为 IP20（室内）或 IP65（室外/防尘防水）。
• 抗冲击/振动：
  • 符合 IEC 60068-2-27 和 IEC 60068-2-6 标准。

---

4. 通信与控制

• 通信接口：
  • 支持 Modbus RTU/TCP、EtherNet/IP、Profinet 等工业协议。
• 控制信号：
  • 干触点输入（无源）或 24VDC 有源信号。
• 反馈信号：
  • 开关状态反馈（常开/常闭触点）。

---

5. 安全与认证

• 安全标准：
  • 符合 IEC 60947-5-1、UL 508、CSA C22.2 No. 14 等标准。
• 认证：
  • CE、UL、cULus、CCC 等。

---

6. 其他特性

• 远程监控：
  • 支持状态监测和故障诊断（需配合上位机系统）。
• 自诊断功能：
  • 内置过载、短路、过热保护。
• 扩展性：
  • 可选配辅助触点、浪涌抑制器等附件。

---

注意事项

1. 型号确认：
   RTXRRN 可能是特定系列或定制型号，建议联系 GE 官方或授权代理商获取详细技术手册。
2. 负载类型：
   技术参数可能因负载类型（如电阻性、电感性、电容性）而有所差异。
3. 环境适应性：
   对于特殊环境（如高海拔、腐蚀性气体），需选择增强型产品。

---

如需更精确的技术参数，建议访问 GE 官方网站 或联系 GE 技术支持团队，提供具体型号和应用场景以获取定制化解决方案。

Technical parameters of General Electric RTXRRN automatic electric remote control switch

Due to the numerous and constantly updated product models of General Electric (GE), the specific technical parameters of RTXRRN automated electric remote control switches may vary depending on product versions, application scenarios, or customization requirements. However, based on the general technical characteristics and industry standards of GE industrial automation products, it can be inferred that this model may include the following key technical parameters:

1. Electrical parameters
Rated voltage:
Usually supports industrial standard voltages such as 24VDC, 120VAC, 240VAC, or 480VAC.
Rated current:
Depending on the load type, the current range may be 5A to 100A, depending on the rated capacity of the switch.
Power factor:
Usually ranging from 0.8 to 1.0 (inductive load).
Insulation resistance:
Generally not less than 10M Ω (tested at 500VDC).
Dielectric strength:
Usually 2000VAC (1 minute, no breakdown).
2. Mechanical parameters
Operation method:
Electric operation, supporting remote control (such as PLC, DCS, or SCADA systems).
Number of operation cycles:
The mechanical lifespan is usually over 1 million cycles, while the electrical lifespan may range from 100000 to 500000 cycles depending on the type of load.
Operation time:
Closing time: ≤ 50ms
Disconnecting time: ≤ 30ms
Installation method:
DIN rail installation or panel installation.
3. Environmental parameters
Working temperature:
-25 ° C to+70 ° C (standard type), or -40 ° C to+85 ° C (wide temperature type).
Storage temperature:
-40 ° C to+85 ° C.
Relative humidity:
5% to 95% (no condensation).
Protection level:
Usually IP20 (indoor) or IP65 (outdoor/dustproof and waterproof).
Anti impact/vibration:
Compliant with IEC 60068-2-27 and IEC 60068-2-6 standards.
4. Communication and Control
Communication interface:
Supports industrial protocols such as Modbus RTU/TCP, EtherNet/IP, Profinet, etc.
Control signal:
Dry contact input (passive) or 24VDC active signal.
Feedback signal:
Switch status feedback (normally open/normally closed contacts).
5. Security and authentication
Safety standards:
Compliant with standards such as IEC 60947-5-1, UL 508, CSA C22.2 No. 14, etc.
authentication:
CE, UL, cULus, CCC, etc.
6. Other characteristics
Remote monitoring:
Support status monitoring and fault diagnosis (requires cooperation with the upper computer system).
Self diagnostic function:
Built in overload, short circuit, and overheating protection.
Scalability:
Optional accessories such as auxiliary contacts and surge suppressors are available.
precautions
Model confirmation:
RTXRRN may be a specific series or customized model. It is recommended to contact GE official or authorized agents for detailed technical manuals.
Load type:
Technical parameters may vary depending on the type of load (such as resistive, inductive, capacitive).
Environmental adaptability:
For special environments such as high altitude and corrosive gases, enhanced products should be selected.
For more precise technical parameters, it is recommended to visit the official GE website or contact the GE technical support team to provide specific models and application scenarios for customized solutions.